|
Author
|
Message
|
|
Park Olson
|
|
|
Group: Forum Members
Last Active: 7 Years Ago
Posts: 102,
Visits: 1.9K
|
OK,,,,
|
|
|
|
|
Hollow Head
|
|
|
Group: Forum Members
Last Active: Last Year
Posts: 1.0K,
Visits: 3.7K
|
 El Cheapo oil filler system? .
 Seppo from Järvenpää, Finland
www.hollowheads.net (just click the hole in the head to proceed)
|
|
|
|
|
mctim64
|
|
|
Group: Forum Members
Last Active: 5 Years Ago
Posts: 2.4K,
Visits: 5.0K
|
Park Olson (4/30/2012)
OK,,,,No biggie, just sayin'. 
 God Bless.  Tim http://yblockguy.com/
350ci Y-Block FED "Elwood", 301ci Y-Block Unibody LSR "Jake", 312ci Y-Block '58 F-100, 338ci Y-Block powered Model A Tudor
tim@yblockguy.com Visalia, California Just west of the Sequoias
|
|
|
|
|
mctim64
|
|
|
Group: Forum Members
Last Active: 5 Years Ago
Posts: 2.4K,
Visits: 5.0K
|
El Mirage in two weeks! New engine is going in today right after I have lunch. I'll let you know how it went tonight. 
bla
God Bless. Tim http://yblockguy.com/ 350ci Y-Block FED "Elwood", 301ci Y-Block Unibody LSR "Jake", 312ci Y-Block '58 F-100, 338ci Y-Block powered Model A Tudor
tim@yblockguy.com Visalia, California Just west of the Sequoias
|
|
|
|
|
MoonShadow
|
|
|
Group: Forum Members
Last Active: Yesterday
Posts: 4.5K,
Visits: 37.1K
|
Jeez, you get lunch too! Chuck
Y's guys rule!
Looking for McCullouch VS57 brackets and parts. Also looking for 28 Chrysler series 72 parts. And early Hemi parts.
 
MoonShadow, 292 w/McCulloch, 28 Chrysler Roadster, 354 Hemi)
Manchester, New Hampshire
|
|
|
|
|
mctim64
|
|
|
Group: Forum Members
Last Active: 5 Years Ago
Posts: 2.4K,
Visits: 5.0K
|
OK! New engine is in and tomorrow will be break-in time. I forgot how hard it is to seperate the engine from the trans. with the scatter shield in place. Oh well, it's done now. 
 
All done! 
bla bla
God Bless. Tim http://yblockguy.com/ 350ci Y-Block FED "Elwood", 301ci Y-Block Unibody LSR "Jake", 312ci Y-Block '58 F-100, 338ci Y-Block powered Model A Tudor
tim@yblockguy.com Visalia, California Just west of the Sequoias
|
|
|
|
|
Ketterbros
|
|
|
Group: Forum Members
Last Active: 7 Years Ago
Posts: 132,
Visits: 2.8K
|
Great work.. Mesquite
 Brother and I own/operate 1957 Ford Fairlane 312/4x2 and two 1963 Falcons 302 rollers carburated 600cfm, FE427 sitting in shed..
|
|
|
|
|
Hollow Head
|
|
|
Group: Forum Members
Last Active: Last Year
Posts: 1.0K,
Visits: 3.7K
|
Sweat, blood and beer. That's all it takes . And a little while... hope it breaks in good.
Seppo from Järvenpää, Finland
www.hollowheads.net (just click the hole in the head to proceed)
|
|
|
|
|
mctim64
|
|
|
Group: Forum Members
Last Active: 5 Years Ago
Posts: 2.4K,
Visits: 5.0K
|
OK! Here it is, 20 min. run time. Now to change the heads.
__________________ bla bla
God Bless. Tim http://yblockguy.com/ 350ci Y-Block FED "Elwood", 301ci Y-Block Unibody LSR "Jake", 312ci Y-Block '58 F-100, 338ci Y-Block powered Model A Tudor
tim@yblockguy.com Visalia, California Just west of the Sequoias
|
|
|
|
|
mctim64
|
|
|
Group: Forum Members
Last Active: 5 Years Ago
Posts: 2.4K,
Visits: 5.0K
|
I think we did well for our first time out with a new engine. First pass the engine felt GREAT! and sounded great too. But when I got the timing slip the #s were the same as last year.  I have a higher gear ratio and went through the traps at the same rpm as last year, should have been close to 140 but was 126. Traction problems again! We lined up for our second pass late in the day with no other changes than a little less air in the tires, we had a bit of trouble with the tow vehicle on the way down that had to be fixed so we got a lat start but that's another story, when we got to the front of the line they shut down for the day. No problem that means we get first run in the morning on a fresh course.  Sunday morning we lined up after the drivers meeting, warmed up the engine, cleared for the course and we were off! The lake bed wasn't the best but since it wasn't tore up bay a bunch of cars before me we got 131 mph! not bad but still we want to go faster, duh. A third and final run is set up for this time I decided to run with the front half of the bed cover off, Charlie will like that. Well, with that the only change and out on a soft tore up lake bed again we managed 132 mph. I think we are on the right track.
I need to add some weight to the back again and there is still some tuning to be done to the engine, timing and mixture but I think we can manage 140 before the year is out and 150 may just happen at Bonneville. The truck is still accelerating at the end on the 1.3 miles at Elmo.
We made the t-shirt and poster too! 
|
God Bless. Tim http://yblockguy.com/ 350ci Y-Block FED "Elwood", 301ci Y-Block Unibody LSR "Jake", 312ci Y-Block '58 F-100, 338ci Y-Block powered Model A Tudor
tim@yblockguy.com Visalia, California Just west of the Sequoias
|
|
|
|