|
Author
|
Message
|
|
Y block Billy
|
|
|
Group: Forum Members
Last Active: 7 Years Ago
Posts: 1.6K,
Visits: 5.2K
|
Glenn, all my condolences go out to you, I just lost my step mother of 38 years this past weekend, But as said, they are in a better place without pain. she was in her 80's and it was just her time. Regards, Bill
 55 Vicky & customline 58 Rack Dump, 55 F350 yard truck, 57 F100 59 & 61 P 400's, 58 F100 custom cab, 69 F100, 79 F150, 82 F600 ramp truck, 90 mustang conv 7 up, 94 Mustang, Should I continue?
|
|
|
|
|
Ted
|
|
|
Group: Administrators
Last Active: 2 days ago
Posts: 7.5K,
Visits: 205.8K
|
My condolences for the loss of a friend. She is now in a better place and without pain.
  Lorena, Texas (South of Waco)
|
|
|
|
|
JPotter57
|
|
|
Group: Forum Members
Last Active: 9 Years Ago
Posts: 144,
Visits: 1.2K
|
I'm sorry to hear about your friend, Glen. You're right, cancer is a terrible thing.
James Potter
`57 Fords International
`57 Custom Tudor
`57 Fords International National Director
Pass Christian, MS (near Gulfport/Biloxi)
|
|
|
|
|
mctim64
|
|
|
Group: Forum Members
Last Active: 6 Years Ago
Posts: 2.4K,
Visits: 5.0K
|
So sorry Glen.
 God Bless.  Tim http://yblockguy.com/
350ci Y-Block FED "Elwood", 301ci Y-Block Unibody LSR "Jake", 312ci Y-Block '58 F-100, 338ci Y-Block powered Model A Tudor
tim@yblockguy.com Visalia, California Just west of the Sequoias
|
|
|
|
|
Glen Henderson
|
|
|
Group: Forum Members
Last Active: 9 Years Ago
Posts: 1.4K,
Visits: 7.5K
|
Thanks Tim, sadly my friend (actually my ex sister in law) pasted last night. We were as close as if we had been blood related even after all these years. She will be missed, but tonight she is pain free and in a much better place. Cancer is such an evil thing, maybe someday a cure will be found.
Glen Henderson
Freedom is not Free
Letohatchee, AL
|
|
|
|
|
mctim64
|
|
|
Group: Forum Members
Last Active: 6 Years Ago
Posts: 2.4K,
Visits: 5.0K
|
Good to hear about the progress Glen! Sorry to hear about your friends, the car will be there but your friends are # 1. I wish you and them the best.
God Bless. Tim http://yblockguy.com/ 350ci Y-Block FED "Elwood", 301ci Y-Block Unibody LSR "Jake", 312ci Y-Block '58 F-100, 338ci Y-Block powered Model A Tudor
tim@yblockguy.com Visalia, California Just west of the Sequoias
|
|
|
|
|
Glen Henderson
|
|
|
Group: Forum Members
Last Active: 9 Years Ago
Posts: 1.4K,
Visits: 7.5K
|
OK, I got my Y Block mag today and it was suggested by Bill and Bob Martin that it was time for a update. I have plans of an artical for the mag if I ever get around to it. I have driven the car around the yard a few times and today even got it out on a back street. I ran into a problem with getting the driveshaft cut. The guy that does it at the local driveline shop had heart surgery and was out of work for awhile. I got the shaft back last week. Next was sorting out the wiring for the elec water pump and fan and getting the line loc plumbed and wired. Still not satisfied with the brakes, I may have to install a brake bias valve to get enough front brake in it. Still have to wire in the trans brake. I ordered the seat belts and a new helmet today, should be in Sat. Just finishing up a few small details, but they all seem to cost money. I had planned on loading it up and taking it to the local scales and weighing it tomorrow, but I have a good friend in the hospital that I need to go see, so I will most likely do that next week.
Glen Henderson
Freedom is not Free
Letohatchee, AL
|
|
|
|
|
Glen Henderson
|
|
|
Group: Forum Members
Last Active: 9 Years Ago
Posts: 1.4K,
Visits: 7.5K
|
That is the same setup that I have.
Glen Henderson
Freedom is not Free
Letohatchee, AL
|
|
|
|
|
yfreak57
|
|
|
Group: Forum Members
Last Active: 9 Months Ago
Posts: 100,
Visits: 1.0K
|
Glen Henderson (5/19/2011)
The kit comes with some stud adapters that are used with a stock dia converter, but since I am running a 10" 3500 stall, I had to come up with a way to adapt it. Thus the alum spacers that sandwich the converter to the flexplate. If anyone is ever in a simular situation, let me know. I had to pay for a cad program to cut the plates on a waterjet, but the shop that I used has them on file now so the next batch should be cheaper.Glen, I have almost identical combination in my wagon with Flat-o-Matic adapter. Look my solution: http://www.y-blocksforever.com/forums/FindPost28123.aspx  .
-jyrki from Finland-www.hollowheads.net 
|
|
|
|
|
charliemccraney
|
|
|
Group: Moderators
Last Active: 2 hours ago
Posts: 6.1K,
Visits: 443.0K
|
I can do it.
Lawrenceville, GA
|
|
|
|