Author
|
Message
|
MattsY
|
|
Group: Forum Members
Last Active: 3 Years Ago
Posts: 82,
Visits: 3.6K
|
Anyone ever try one of these adapters to use a PCV valve from the rear breather hole in the valley cover? Yes, it's a road draft conversion for a small block scruby, but it looks like it'll fit nicely!
|
|
|
PF Arcand
|
|
Group: Forum Members
Last Active: 8 Months Ago
Posts: 3.3K,
Visits: 238.8K
|
Is that for an in line pcv ?
Paul
|
|
|
MattsY
|
|
Group: Forum Members
Last Active: 3 Years Ago
Posts: 82,
Visits: 3.6K
|
Yup, for an inline PCV. This seems very similar to an original Ford part that I'm told is rare and hard to come by.
|
|
|
56_Fairlane
|
|
Group: Forum Members
Last Active: 2 Years Ago
Posts: 575,
Visits: 14.6K
|
I found an original one for mine. I would try one of these if I hadn't found one.
~DJ~ AKA "Bleach" 1956 Ford Fairlane Town Sedan 30K original miles
|
|
|
miker
|
|
Group: Forum Members
Last Active: Last Week
Posts: 1.8K,
Visits: 183.3K
|
I've used these on couple engines. You need to make sure there's a baffle under it, if you've got an aluminum valley pan you have to add one. Otherwise you'll suck a ton of oil. https://www.jegs.com/i/JEGS/555/52225/10002/-1
miker 55 bird, 32 cabrio F code Kent, WA Tucson, AZ
|
|
|
30 coupe
|
|
Group: Forum Members
Last Active: 2 Months Ago
Posts: 130,
Visits: 3.4K
|
I have a couple of the Ford ones, but they would not work with the Edelbrock 3x2 intake I just put on my car. I ended up modifying the valley pan and used a regular small block ford pcv valve and rubber grommet
|
|
|
darrell
|
|
Group: Forum Members
Last Active: 7 days ago
Posts: 452,
Visits: 21.1K
|
ive used them before to make a pcv setup.they are not that hard to find if your in an area with lots of old trucks junked.63 and 64 with a 2 bbl carb had them.not sure if they had any earlier.
|
|
|
MattsY
|
|
Group: Forum Members
Last Active: 3 Years Ago
Posts: 82,
Visits: 3.6K
|
I'm using the original valley pan, so it's baffled. I would just use a PCV valve in the hole with a grommet, but the threaded hold down stud for the breather tube is still there and in the way. It knocks out through the bottom and I don't really want to take the manifold off to remove the tray.
|
|
|
darrell
|
|
Group: Forum Members
Last Active: 7 days ago
Posts: 452,
Visits: 21.1K
|
any i seen juts screwed out from the top
|
|
|
charliemccraney
|
|
Group: Moderators
Last Active: 24 minutes ago
Posts: 6.1K,
Visits: 437.3K
|
Original was a screw, not a stud. If it is simply a stud, then it should come out but if the previous owner used loctite to ensure that it doesn't move when tightened or even had a bolt welded to the bottom or something else, then it may not come out very easily.
Lawrenceville, GA
|
|
|