Hitting on all eight cylinders
Group: Forum Members
Last Active: 11 Years Ago
Posts: 2,
Visits: 6
|
Hello everyone, I have a '50 Ford customline 4 door sedan that I am turning into a custom (trying to achieve a "Mini-Merc" theme). I am pulling the flathead and going to put in a Y block out of a 50's T-bird, not too interested in building it up too much, but want enough that I am not a snail...intend to back the Y block with an AOD, and need to know what adapter to use for the most painless installation. I am in a wheelchair, so will have to have others assemble for me so need something fairly straightforward LOL 
Raised on gasoline and still have tetraethyl coursing through my veins....
|
|
Group: Forum Members
Last Active: 5 hours ago
Posts: 4.5K,
Visits: 37.1K
|
I used this adapter on mine several years ago and had no problems. http://www.transmissionadapters.com/Pricing.htmOur best friend in Y-Block parts is John Mummert in El Cajon, CA. He has this one: http://www.ford-y-block.com/c4adapt.htmWhile you are there take a look at ALL on the products John offers for Y's. Everything you need to build from mild to wild. There are others around. Just do an EBAY search. Chuck
Y's guys rule!
Looking for McCullouch VS57 brackets and parts. Also looking for 28 Chrysler series 72 parts. And early Hemi parts.
 
MoonShadow, 292 w/McCulloch, 28 Chrysler Roadster, 354 Hemi)
Manchester, New Hampshire
|
|
Group: Forum Members
Last Active: 58 minutes ago
Posts: 549,
Visits: 8.3K
|
A y-block into a 49/51 Ford or Merc is one of the hardest swaps you can do. In 1964 a friend and myself put a 56 T-Bird engine into a 51 Ford convertable, getting the engine and trans in is the easy part (as long as you have the motor mounts that bolt to the timming case cover) To start with you need a Thunderbird timming case cover, and oil pan, and a dropped tie rod. After that you must make everything, exhaust, oil filter, linkage. My friend's father had a big auto repair business and I was working part time in a michine shop, we must of had over a 150 hours in that car in the 4 months it took to finish. The upside...we put over 50,000 miles on that can in the next 3 years, with the only repair being a front seal in the engine.
|
Hitting on all eight cylinders
Group: Forum Members
Last Active: 11 Years Ago
Posts: 2,
Visits: 6
|
Thank you very much Moon Shadow and Lou for your insights. 
Raised on gasoline and still have tetraethyl coursing through my veins....
|
|
Group: Forum Members
Last Active: 2 Weeks Ago
Posts: 460,
Visits: 4.4K
|
MoonShadow, how did you go mounting the AOD, JMummert advises that the ear on the block blocks the AOD starter motor hole?Did you modify the block?
South Australia
|
|
Group: Forum Members
Last Active: 5 hours ago
Posts: 4.5K,
Visits: 37.1K
|
The Benedtson adapter is about 1" thick and comes with a high torque starter that bolts right up to it. There is a bit of grinding to do on the AOD bell housing but it is minimal. Makes starter swaps a whole lot easier. I did have to replace the starter once but its the same one that is used on the scrubs (sbc). Chuck
Y's guys rule!
Looking for McCullouch VS57 brackets and parts. Also looking for 28 Chrysler series 72 parts. And early Hemi parts.
MoonShadow, 292 w/McCulloch, 28 Chrysler Roadster, 354 Hemi)
Manchester, New Hampshire
|
|
Group: Forum Members
Last Active: 2 Weeks Ago
Posts: 460,
Visits: 4.4K
|
Thanks Chuck, gives me another option to get the revs down.
My ute with 302w, AOD and 3.55's is barely above idle @ 100kmh (65mph).
South Australia
|
|
Group: Forum Members
Last Active: 5 hours ago
Posts: 4.5K,
Visits: 37.1K
|
It has enabled me to run 4:10 gears on the street and still have low Rpm on the highway. Only better option is a 5 or 6 speed and I like my automatics. Chuck
Y's guys rule!
Looking for McCullouch VS57 brackets and parts. Also looking for 28 Chrysler series 72 parts. And early Hemi parts.
MoonShadow, 292 w/McCulloch, 28 Chrysler Roadster, 354 Hemi)
Manchester, New Hampshire
|