|
Author
|
Message
|
|
Oldmics
|
|
|
Group: Forum Members
Last Active: 4 Years Ago
Posts: 710,
Visits: 78.1K
|
Dropped my third 312 crank off at my machinest today for evaluation. He told me that a customer had bumped into one of my my ECZ cranks that I had left him for inspection and it had fallen over and broken in two  It had not been inspected. I figure that there are two ways to look at this situation-either call it a loss and dont worry about it since it may have been ultimatly cracked and finally went OR it fell just so exact to do the damange to a good crank and I"m owed something. Wadduya think gang? Oldmics
|
|
|
|
|
oldcarmark
|
|
|
Group: Forum Members
Last Active: Last Month
Posts: 3.7K,
Visits: 32.4K
|
What did the machinist say?
 
|
|
|
|
|
mctim64
|
|
|
Group: Forum Members
Last Active: 5 Years Ago
Posts: 2.4K,
Visits: 5.0K
|
If it broke in two just by being knocked over it wasn't a very good crank to begin with.
 God Bless.  Tim http://yblockguy.com/
350ci Y-Block FED "Elwood", 301ci Y-Block Unibody LSR "Jake", 312ci Y-Block '58 F-100, 338ci Y-Block powered Model A Tudor
tim@yblockguy.com Visalia, California Just west of the Sequoias
|
|
|
|
|
aussiebill
|
|
|
Group: Forum Members
Last Active: 4 Years Ago
Posts: 1.8K,
Visits: 11.4K
|
oldcarmark (5/23/2011)
What did the machinist say?Usually if crank was cracked leading to it breaking then there should? be telltale shiney/dark areas where break occured? maybe not but at least have a look or get opinion, but was probably weak to break by falling over as tim mentions.
 AussieBill YYYY Forever Y Block YYYY Down Under, Australia
|
|
|
|
|
PF Arcand
|
|
|
Group: Forum Members
Last Active: 9 Months Ago
Posts: 3.3K,
Visits: 238.8K
|
You said the 3rd crank.. what happened to the other one?
Paul
|
|
|
|
|
Ted
|
|
|
Group: Administrators
Last Active: 2 days ago
Posts: 7.3K,
Visits: 204.6K
|
I’ll agree with Tim in that if the crankshaft broke simply by falling over, it was already a problem in the making. When leaving parts at any machine shop, be sure to mark your parts before "dropping them" off to keep everyone ‘honest’.
  Lorena, Texas (South of Waco)
|
|
|
|
|
The Master Cylinder
|
|
|
Group: Forum Members
Last Active: 3 Years Ago
Posts: 974,
Visits: 6.2K
|
Ted, Is that a pun?? "Before dropping them off". Sorry, 6 in the morning... Ted (5/24/2011)
When leaving parts at any machine shop, be sure to mark your parts before dropping them off to keep everyone ‘honest’.
 "The Master Cylinder"
Enjoying life at the beach in SOCAL 
|
|
|
|
|
Oldmics
|
|
|
Group: Forum Members
Last Active: 4 Years Ago
Posts: 710,
Visits: 78.1K
|
Machinest said " I guess I owe you a crank". My thinking is like Tims in it probably was not a good piece to start with BUT it was left in his care for evaluation. The other one of the two is O.K. and being ground. It is my crank as I knew the markings.I will reinspect both pieces of it for flaws. I think it best to ascertain a value on a replacement crank and just have him knock that amount off my bill. Nice comment about "dropping the crank off"- It cracked me up (pun intended :w00t Thanks for the input. Oldmics
|
|
|
|
|
MoonShadow
|
|
|
Group: Forum Members
Last Active: Yesterday
Posts: 4.5K,
Visits: 37.1K
|
I think the machinist is being honest about it. Many would just say tough luck and talk about previous damage. Knocking off on the bill would be appropriate. Chuck
Y's guys rule!
Looking for McCullouch VS57 brackets and parts. Also looking for 28 Chrysler series 72 parts. And early Hemi parts.
 
MoonShadow, 292 w/McCulloch, 28 Chrysler Roadster, 354 Hemi)
Manchester, New Hampshire
|
|
|
|
|
The Master Cylinder
|
|
|
Group: Forum Members
Last Active: 3 Years Ago
Posts: 974,
Visits: 6.2K
|
Oldmics (5/24/2011)
Machinest said " I guess I owe you a crank".
OldmicsAll joking aside, sounds like your machinist is a stand up guy, unfortunately not too many around these days.
"The Master Cylinder"
Enjoying life at the beach in SOCAL
|
|
|
|