Profile Picture

Cleaning up an intake manifold???

Posted By Deyomatic 4 Months Ago
You don't have permission to rate!
Author
Message
Deyomatic
Posted 4 Months Ago
View Quick Profile
Supercharged

Supercharged (722 reputation)Supercharged (722 reputation)Supercharged (722 reputation)Supercharged (722 reputation)Supercharged (722 reputation)Supercharged (722 reputation)Supercharged (722 reputation)Supercharged (722 reputation)Supercharged (722 reputation)

Group: Forum Members
Last Active: Yesterday
Posts: 239, Visits: 1.3K
I got a good deal on an ECZ-9425B manifold and I'm in the process of getting it prepped for paint to put it on after smoothing out the venturi holes a little...

Is there something I can soak it in that will get rid of the rust in the thermostat area, as well as any other surface rust as well as the heat riser ports?

Thanks.




Threaded View

Threaded View
Forum Post Cleaning up an intake manifold??? By Deyomatic ( 4 Months Ago )
Forum Post I know that I will probably get some negative comments in response to... By alanfreeman ( 4 Months Ago )
Forum Post Depending upon the amount of rust, you might consider having it media... By 55blacktie ( 4 Months Ago )
Forum Post Another good idea would be to use electrolysis. For something as small... By Daniel Jessup ( 4 Months Ago )
Forum Post Thank you...three great ideas. Daniel- do you think the electrolysis... By Deyomatic ( 4 Months Ago )
Forum Post The electrolysis works well if you are willing to be patient with it.... By Daniel Jessup ( 4 Months Ago )
Forum Post I may just try to have it blasted somewhere. It's not as crusty as I... By Deyomatic ( 4 Months Ago )
Forum Post I have sandblasted both cast iron intakes and aluminum intakes before... By Joe-JDC ( 4 Months Ago )
Forum Post Thanks Joe, Should I get 80 grit or 120 aluminum oxide…or something... By Deyomatic ( 4 Months Ago )
Forum Post Which ever one you have, adjust the pressure to get a rough texture on... By Joe-JDC ( 4 Months Ago )
Forum Post I will try the 120 then. Thanks again. The only paint “quality” I... By Deyomatic ( 4 Months Ago )
Forum Post You'll need to remove oil/grease, etc. before it's media blasted;... By 55blacktie ( 4 Months Ago )
Forum Post If media blasting is done properly, it will remove all greases,... By Joe-JDC ( 4 Months Ago )
Forum Post HMMMM... Could I hit the suspect areas with brake cleaner or even a... By Deyomatic ( 4 Months Ago )
Forum Post When my heads came back from the machine shop, I thought they were... By 55blacktie ( 4 Months Ago )
Forum Post Thanks for the tip...I had planned on using acetone but I do have a... By Deyomatic ( 4 Months Ago )
Forum Post I used a cheap brass-wire brush for scrubbing, cheap paint brushes for... By 55blacktie ( 4 Months Ago )
Forum Post I plan to do the same with a manifold that I just picked up. I can... By Skyliner57 ( 3 Months Ago )
Forum Post Are you retaining the original heat-riser choke? By 55blacktie ( 3 Months Ago )
Forum Post The heat riser tube replacement is a 10 minute job with the manifold... By cokefirst ( 3 Months Ago )
Forum Post I had not planned go remove, the car starts extremely well. I see... By Skyliner57 ( 2 Months Ago )
Forum Post You have a 56 FORD and you are putting a 1957 ECZ-B intake on it? Each... By KULTULZ ( 2 Months Ago )


Reading This Topic


Site Meter