|
Group: Forum Members
Last Active: 20 minutes ago
Posts: 2.0K,
Visits: 118.6K
|
Like the title says, I am looking for ECG 6564 rocker arms - but I only need 6, maybe you have a few or more lying around. Also looking to purchase rocker arm shaft springs - need 6 of those as well. Give me a full price (+shipping) to 45140 if you have them. My email address is danaxjessup@yahoo.com or you can also leave a message on my website, www.hotrodreverend.com. I do check PM's on this forum of course. Thanks! EDIT on 4/22: found new springs from Rocker Arms Unlimited...
Daniel JessupLancaster, California aka "The Hot Rod Reverend" 
check out the 1955 Ford Fairlane build at www.hotrodreverend.com
|
|
Group: Forum Members
Last Active: 7 days ago
Posts: 452,
Visits: 21.1K
|
did you ever get your rockers
|
|
Group: Forum Members
Last Active: 20 minutes ago
Posts: 2.0K,
Visits: 118.6K
|
I did get the springs from Rocker Arms Unlimited - they were very helpful and things went well. However, I have not had any leads on ECG rockers but that is ok. The individual who called me today only needs the 1.43 I am told. His engine builder is supposed to contact me this week. However, it would be nice to be able to complete what I have on hand just for the future.
Daniel JessupLancaster, California aka "The Hot Rod Reverend"
check out the 1955 Ford Fairlane build at www.hotrodreverend.com
|
|
Group: Forum Members
Last Active: 7 days ago
Posts: 452,
Visits: 21.1K
|
i have several sets.i sent you an email dont know if you got it or not.anyway if you want 6 you can have them for shipping price.they need refacing.if you want them give me your address.and ill mail them monday.
|
|
Group: Forum Members
Last Active: 20 minutes ago
Posts: 2.0K,
Visits: 118.6K
|
My email is danaxjessup@yahoo.com but I have not seen anything yet. My address is 6218 Spires Drive, Loveland, Ohio 45140 thanks! do let me know how much I owe you for the shipping
Daniel JessupLancaster, California aka "The Hot Rod Reverend"
check out the 1955 Ford Fairlane build at www.hotrodreverend.com
|
|
Group: Forum Members
Last Active: 7 days ago
Posts: 452,
Visits: 21.1K
|
ill get them in the mail tomorrow take a good week to reach you.ill put my address in side.do you need any small parts that i can put in the box.with them.have a lot of junk ill never use.
|
|
Group: Forum Members
Last Active: 20 minutes ago
Posts: 2.0K,
Visits: 118.6K
|
If you have any extra of the washers that go on the assemblies, that would be good. The large washers on the ends - two that look standard and the spring washer in the middle?
Daniel JessupLancaster, California aka "The Hot Rod Reverend"
check out the 1955 Ford Fairlane build at www.hotrodreverend.com
|
|
Group: Forum Members
Last Active: 7 days ago
Posts: 452,
Visits: 21.1K
|
sent it this morning with the washers.shipping cost is on the box.sent them as cheap as possible.
|
|
Group: Forum Members
Last Active: 20 minutes ago
Posts: 2.0K,
Visits: 118.6K
|
appreciate it Darrell!
Daniel JessupLancaster, California aka "The Hot Rod Reverend"
check out the 1955 Ford Fairlane build at www.hotrodreverend.com
|
|
Group: Forum Members
Last Active: 11 days ago
Posts: 52,
Visits: 34.1K
|
Hi Darrell,
Would it be possible to get 8 rocker arms? I bought a set of rocker shafts at a swap meet, but only one ended being high ratio. I sent you an email and pm the other day.
Thanks Darrell, and thanks, Daniel, for asking the original question,
Soffian
Soffian Adam
Jamestown, NY
59 F100, 55 Club sedan
|