Profile Picture

HARMONIC BALANCER BOLT

Posted By 55charliebird 5 Years Ago
You don't have permission to rate!
Author
Message
55charliebird
Posted 5 Years Ago
View Quick Profile
Supercharged

Supercharged (600 reputation)Supercharged (600 reputation)Supercharged (600 reputation)Supercharged (600 reputation)Supercharged (600 reputation)Supercharged (600 reputation)Supercharged (600 reputation)Supercharged (600 reputation)Supercharged (600 reputation)

Group: Forum Members
Last Active: 3 Years Ago
Posts: 192, Visits: 39.2K
AM GETTING READY TO INSTALL THE BALANCER.  ANY SUGGESTIONS ON "SHOULD I USE THE EXISTING CRANKSHAFT BOLT OR SHOULD I GET A NEW ONE"?   MY CONCERN IS "CAN THE OLD BOLT TAKE THE 90 LB. TORQUE.?  MY EXPERIENCE WITH MERCEDES BOLTS IS THAT THEY DON'T  RECOMMEND REUSING OLD BOLTS BECAUSE THEY ARE STRESSED AND STRETCHED  AND MAY GIVE WAY.  THANKS
darrell
Posted 5 Years Ago
View Quick Profile
Supercharged

Supercharged (1.0K reputation)Supercharged (1.0K reputation)Supercharged (1.0K reputation)Supercharged (1.0K reputation)Supercharged (1.0K reputation)Supercharged (1.0K reputation)Supercharged (1.0K reputation)Supercharged (1.0K reputation)Supercharged (1.0K reputation)

Group: Forum Members
Last Active: 43 minutes ago
Posts: 442, Visits: 20.0K
they will stand 90 and more.reuse.
MoonShadow
Posted 5 Years Ago
View Quick Profile
Supercharged

Supercharged (7.4K reputation)Supercharged (7.4K reputation)Supercharged (7.4K reputation)Supercharged (7.4K reputation)Supercharged (7.4K reputation)Supercharged (7.4K reputation)Supercharged (7.4K reputation)Supercharged (7.4K reputation)Supercharged (7.4K reputation)

Group: Forum Members
Last Active: 2 hours ago
Posts: 4.5K, Visits: 36.1K
When I did my blower setup I needed a longer bolt and got it from http://www.kljack.com/ We have a store locally so I just took the stock one over and they actually had the bolt I needed in stock. They can also order. I also buy stainless steel bolts from them and they are generally cheaper.

Y's guys rule!
Looking for McCullouch VS57 brackets and parts. Also looking for 28 Chrysler series 72 parts. And early Hemi parts.

MoonShadow, 292 w/McCulloch, 28 Chrysler Roadster, 354 Hemi)
Manchester, New Hampshire
paul2748
Posted 5 Years Ago
View Quick Profile
Supercharged

Supercharged (6.5K reputation)Supercharged (6.5K reputation)Supercharged (6.5K reputation)Supercharged (6.5K reputation)Supercharged (6.5K reputation)Supercharged (6.5K reputation)Supercharged (6.5K reputation)Supercharged (6.5K reputation)Supercharged (6.5K reputation)

Group: Forum Members
Last Active: 10 hours ago
Posts: 3.5K, Visits: 469.2K
I've used the stock bolt over again in a couple of engines with no problems.


54 Victoria 312;  48 Ford Conv 302, 56 Bird 312
Forever Ford
Midland Park, NJ

Talkwrench
Posted 5 Years Ago
View Quick Profile
Supercharged

Supercharged (1.6K reputation)Supercharged (1.6K reputation)Supercharged (1.6K reputation)Supercharged (1.6K reputation)Supercharged (1.6K reputation)Supercharged (1.6K reputation)Supercharged (1.6K reputation)Supercharged (1.6K reputation)Supercharged (1.6K reputation)

Group: Forum Members
Last Active: 3 Years Ago
Posts: 898, Visits: 23.2K
90lbs no Problem.. Try doing up an early Ford rear axle nut [they're not big].. Over 200 lbs that'll make you pucker!

http://forums.y-blocksforever.com/Uploads/Images/02c74785-3ce2-4b80-a66c-f31f.jpg

"Came too close to dying to stop living now!"
55charliebird
Posted 5 Years Ago
View Quick Profile
Supercharged

Supercharged (600 reputation)Supercharged (600 reputation)Supercharged (600 reputation)Supercharged (600 reputation)Supercharged (600 reputation)Supercharged (600 reputation)Supercharged (600 reputation)Supercharged (600 reputation)Supercharged (600 reputation)

Group: Forum Members
Last Active: 3 Years Ago
Posts: 192, Visits: 39.2K
NO FEAR, THE OLD BOLT WORKED FINE.  90LBS AND HOLDING   THANKS


Reading This Topic


Site Meter