Profile Picture

Powerbond damper

Posted By 62bigwindow 7 Years Ago
You don't have permission to rate!

Powerbond damper

Author
Message
62bigwindow
Posted 7 Years Ago
View Quick Profile
Supercharged

Supercharged (2.1K reputation)Supercharged (2.1K reputation)Supercharged (2.1K reputation)Supercharged (2.1K reputation)Supercharged (2.1K reputation)Supercharged (2.1K reputation)Supercharged (2.1K reputation)Supercharged (2.1K reputation)Supercharged (2.1K reputation)

Group: Forum Members
Last Active: 9 Months Ago
Posts: 884, Visits: 14.3K
I had to buy a new damper for my car. For some reason the replacements ID is smaller than the original Ford damper. So I'm going to have to have it honed out . How much press should it have? I was thinking maybe less than .001 Would be sufficient. Also I read somewhere once where the key slot is in relation to the TDC mark but I can't seem to find that info. Can anyone help me out with either. Thanks

Durham Missouri

Threaded View

Threaded View
Forum Post Powerbond damper By 62bigwindow ( 7 Years Ago )
Forum Post , I have also found them to be tight fit and polished out to orig... By aussiebill ( 7 Years Ago )
Forum Post Replaced the damper on my stock 292 with a Powerbond brand, at the... By Tedster ( 7 Years Ago )
Forum Post There's no way it's going on. It started to and then stopped, galled... By 62bigwindow ( 7 Years Ago )
Forum Post Not that I have ever measured any but I would have thought that ever... By ian57tbird ( 7 Years Ago )
Forum Post They can be a $&@!! to install, but they shouldn't be. Powerbond makes... By Tedster ( 7 Years Ago )
Forum Post That article is more precise, but 50 years ago when Mom wasn’t home, I... By miker ( 7 Years Ago )
Forum Post I've had stock dampers that were difficult to get on. Cleaned up the... By MoonShadow ( 7 Years Ago )
Forum Post I've had the stock one off and on a couple times with no problems. The... By 62bigwindow ( 7 Years Ago )
Forum Post It does sound like you have a clearance problem. Did you contact... By MoonShadow ( 7 Years Ago )
Forum Post "My thinking is if you have to freeze one and heat another to get it... By Tedster ( 7 Years Ago )
Forum Post If the id of the damper really is too small, send an email to... By charliemccraney ( 7 Years Ago )
Forum Post [quote][b]62bigwindow (12/17/2017)[/b][hr]........Also I read... By Ted ( 7 Years Ago )
Forum Post Thanks Ted. That is what I was looking for. I dropped off the damper... By 62bigwindow ( 7 Years Ago )
Forum Post [quote][b]62bigwindow (12/17/2017)[/b][hr]I had to buy a new damper... By Ted ( 7 Years Ago )
Forum Post Thought I post a follow up on this. The machine shop had to open it up... By 62bigwindow ( 7 Years Ago )
Forum Post It may not idle well but at least for test purposes I'd want the idle... By Tedster ( 7 Years Ago )
Forum Post Does the timing jump up when you rev the engine? If not then the... By MoonShadow ( 7 Years Ago )
Forum Post It won't start with 38 degrees of advance so 38 probably is not the... By charliemccraney ( 7 Years Ago )
Forum Post It seemed very close to the drawing Ted posted. I was going to put the... By 62bigwindow ( 7 Years Ago )
Forum Post Ok. I had some free time and did a little work on the car. I changed... By 62bigwindow ( 7 Years Ago )
Forum Post I guess it's possible that you got a bad one. I installed mine before... By 57RancheroJim ( 7 Years Ago )
Forum Post Just another thought. What sort of timing light are you using? I have... By ian57tbird ( 7 Years Ago )
Forum Post It is a dial back. I've never had an issue with it before but... By 62bigwindow ( 7 Years Ago )
Forum Post I’ve used a number of Powerbond harmonic dampers on the Y engines and... By Ted ( 7 Years Ago )
Forum Post I have a notion its a combination of the slipped original... By 62bigwindow ( 7 Years Ago )
Forum Post That doesn't really make sense if you think about it. Seems to me a... By Tedster ( 7 Years Ago )
Forum Post If the new damper is off 2° then my timing light reads 8-10° off then... By 62bigwindow ( 7 Years Ago )


Reading This Topic

Site Meter