How much power are you making with what setup???

Home
»
Keeping The Dream Alive!
»
Racing
»
How much power are you making with what setup???

Posted By babor 9 Years Ago

You don't have permission to rate!

How much power are you making with what setup???

Author	Message
babor	Posted 9 Years Ago
Supercharged Group: Forum Members Last Active: 9 Years Ago Posts: 74, Visits: 80	Pondering over the possibilities of this project I am about to undergo, something came to mind. How much power is average with what modifications and what heads, etc...??? Carbs, cams, transmissions, gear ratios, times in the 1/8-1/4 mile? This should be an interesting thread!
	Reply Quote
Reply
aussiebird	Posted 9 Years Ago
Hitting on all eight cylinders Group: Forum Members Last Active: 9 Years Ago Posts: 3, Visits: 8	Hi all l recently built a y block with mummerts advise and expertise these yblocks are pretty good and very high reving engines forged pistons mummert suppled rods cam heads manifold 750cfm dp holley c4 conversion and a 9inch LSD and l have to say lm impressed and they sound better than any other V8 out there
	Reply Quote

Threaded View

How much power are you making with what setup??? By babor ( 9 Years Ago )

There are likely a hundred variables in play here. And then there's... By PF Arcand ( 9 Years Ago )

Like Paul says, I can only speculate but I can speculate based on... By charliemccraney ( 9 Years Ago )

I have done a fair amount of testing on different combinations of a... By RB ( 9 Years Ago )

Weren't you able to crack 300hp before adding ported heads? I... By charliemccraney ( 9 Years Ago )

I have one of the best cylinder head guys in the country here. He is... By babor ( 9 Years Ago )

We need to keep in mind that prior to about 1972, Detroit was using... By PF Arcand ( 9 Years Ago )

Paul brings up a good point. Having dyno tested a majority of... By Ted ( 9 Years Ago )

60 over, G heads, small cam, B intake, 1.43 rockers, numerous carbs... By 62galxe ( 9 Years Ago )

The other thing worth mentioning is who's dyno it is, and how they... By miker ( 9 Years Ago )

Considering that I can make 500hp EASILY with an SBC, this baby is... By babor ( 9 Years Ago )

I think this guy is from the dark side By Cliff ( 9 Years Ago )

[quote][b]babor (1/21/2015)[/b][hr] Considering that I can make... By Canadian Hot Rodder ( 9 Years Ago )

Easy come easy go! Considering that the engine was for sale last... By Doug T ( 9 Years Ago )

I'm assuming easily is synonymous with cost-effectively in this... By charliemccraney ( 9 Years Ago )

Engines, oh boy, my buddy built a 348 scruby for his 58 and... By brokengate ( 9 Years Ago )

Well, here is an engine I put together a few years ago.. Mostly stock... By RB ( 9 Years Ago )

I just wanna go fast cheap and reliable. No fancy aftermarket parts,... By babor ( 9 Years Ago )

Have your mamma cuddle you ingrate, I think you are done here. By brokengate ( 9 Years Ago )

I don't see how you come up with $4000 for the level of performance... By charliemccraney ( 9 Years Ago )

Thank you Charlie. This is the first positive response to my reply. I... By babor ( 9 Years Ago )

For the record, I have also built Ford 2.3 SOHC engines. I can get... By babor ( 9 Years Ago )

The Y can make however much power you want for your project. A year... By charliemccraney ( 9 Years Ago )

Thank you! As far as it being for sale, I'm just seeing if there are... By babor ( 9 Years Ago )

Babor. It is a Y-Block site so any thoughts of using the Brand X... By Ted ( 9 Years Ago )

I might add, Ted can run high 8's with a carbureted no power adder Y... By pegleg ( 9 Years Ago )

Its funny what things cost these days. I don't think there is such... By John Mummert ( 9 Years Ago )

would like to visit your shop and will be in the area in approx 9... By 2721955meteor ( 9 Years Ago )

I just finished the cost trade for keeping the Y block versus... By Bob Gardner ( 9 Years Ago )

When Ben Barnes dynode my 312 punched out to 345 cu ins. for the... By speedpro56 ( 9 Years Ago )

Babor, The basic design of the Y incorporates many of the copied... By Y block Billy ( 9 Years Ago )

Funny how it has to turn into an argument to get any good answers.... By babor ( 9 Years Ago )

I don't think you have to worry about breaking the tires loose with a... By Y block Billy ( 9 Years Ago )

Billy, What happens if you launch her in 2nd? Lite 'em up??? If this... By babor ( 9 Years Ago )

[quote][b]babor (1/25/2015)[/b][hr] Funny how it has to turn into... By Canadian Hot Rodder ( 9 Years Ago )

http://youtu.be/RdeX6BDjdXA By Canadian Hot Rodder ( 9 Years Ago )

I am not really a" brand man",i have a 78 Malibu with a modified 406... By steinauge ( 9 Years Ago )

Wasn't trying to advocate, just commenting. What rear gear ratio was... By babor ( 9 Years Ago )

[quote][b]steinauge (1/27/2015)[/b][hr] I am not really a" brand... By Canadian Hot Rodder ( 9 Years Ago )

That's an impressive dead punch for a heavy car!! This baby with some... By babor ( 9 Years Ago )

Is that a dead punch or a brake torque? By babor ( 9 Years Ago )

I don't know if a burnout with street tires translates to anything... By charliemccraney ( 9 Years Ago )

Thanks for the input! I hope more people will speak up, that IS why I... By babor ( 9 Years Ago )

If you want to do those crowd pleasing half track burnouts, you... By RB ( 9 Years Ago )

I have a mildly built 40 over 292 that is running a McCulloch... By MoonShadow ( 9 Years Ago )

Cool projects! Great input! Thank you... The repop slicks may be an... By babor ( 9 Years Ago )

Chuck, it must have something to do with the way your car is lowered... By Y block Billy ( 9 Years Ago )

Babor. The amount of power being made will relate directly back to... By Ted ( 9 Years Ago )

Thank you Ted! My cylinder head guy will do extensive work to the... By babor ( 9 Years Ago )

The 505-T is a tried and true combo that is used by several of our... By RB ( 9 Years Ago )

Cool! They are already the big valve heads! I'll just have him do the... By babor ( 9 Years Ago )

Thanks Tim! My cylinder head guy is The real thing. He works on... By babor ( 9 Years Ago )

Assuming a pretty basic overbored 292, you'll need to 0 the deck (mill... By charliemccraney ( 9 Years Ago )

I may be a little late to the party but I just wanted to add that when... By mctim64 ( 9 Years Ago )

[quote][b]mctim64 (1/31/2015)[/b][hr] I'm sure Rob is a good head guy... By NoShortcuts ( 9 Years Ago )

Ha Ha! I just noticed if you type shivey (with a ch) the site... By mctim64 ( 9 Years Ago )

That is AWESOME news! Thank you for your response! I think I will... By babor ( 9 Years Ago )

Charlie, Babor, You can have the heads milled on the intake surfaces... By Y block Billy ( 9 Years Ago )

Cool! Thanks Billy! I was wondering about that because we are likely... By babor ( 9 Years Ago )

[quote][b]babor (2/1/2015)[/b][hr] Cool! Thanks Billy! I was... By Ted ( 9 Years Ago )

I just milled a pair of G heads .030 They cc'd out at 63. By RB ( 9 Years Ago )

Before attempting to mill any Y cylinder head, be sure to measure the... By Ted ( 9 Years Ago )

Ted, 1.4 times .050" = .070" .54 X .050" = .027 I thought it was... By Y block Billy ( 9 Years Ago )

We've been going at the static compression ratio thing, Babor. As... By NoShortcuts ( 9 Years Ago )

YB Billy: re the intake side milling. I got confused on that one also.... By PF Arcand ( 9 Years Ago )

Hi all l recently built a y block with mummerts advise and expertise... By aussiebird ( 9 Years Ago )

Post Reply

Reading This Topic