Big Y block 368 inch lifters, etc.

Author	Message
KULTULZ	Posted 5 Years Ago
Supercharged Group: Forum Members Last Active: 9 hours ago Posts: 1.5K, Visits: 303.3K	____________________________
	Reply Quote
Oldmics	Posted 5 Years Ago
Supercharged Group: Forum Members Last Active: 4 Years Ago Posts: 710, Visits: 78.1K	M335 used the two Hollys as you have already ascertained. Used a tach drive dual point distributor. Heads were cut .060 to raise compression and had a pretty radical camshaft using solid lifters. It was a blueprinted engine assembly. Dont forget those unique looking valve covers. I have repro air filters for the M335 carbs if interested. Oldmics
	Reply Quote
martyk98	Posted 5 Years Ago
Supercharged Group: Forum Members Last Active: Last Year Posts: 160, Visits: 31.8K	Hey Ted, just going through some old postings here ref 368 engines. I'm going to tackle one and still looking to put roller lifters/cam in mine just cuz I can. From what I've read the only difference between a stock 368 Lincoln and the M335 is carburation. Your thoughts?
	Reply Quote
KULTULZ	Posted 6 Years Ago
Supercharged Group: Forum Members Last Active: 9 hours ago Posts: 1.5K, Visits: 303.3K	Again THANX! It may be my browser... ____________________________
	Reply Quote
Ted	Posted 6 Years Ago
Co-Administrator Group: Administrators Last Active: 9 hours ago Posts: 7.3K, Visits: 204.6K	KULTULZ (4/8/2018) Edited 6 minutes ago by Ted THANX TED! What am I doing wrong? I have made this mistake more than once... Don’t know why but your replies ends up being within the quote box. Sort of makes it hard to read on my end. I’m simply going into the post and closing up the gaps around the ‘quote’ markers. You might try putting a hard return after the quote itself when replying and see if that helps. Lorena, Texas (South of Waco)
	Reply Quote
KULTULZ	Posted 6 Years Ago
Supercharged Group: Forum Members Last Active: 9 hours ago Posts: 1.5K, Visits: 303.3K	Edited 6 minutes ago by Ted THANX TED! What am I doing wrong? I have made this mistake more than once... ____________________________
	Reply Quote
KULTULZ	Posted 6 Years Ago
Supercharged Group: Forum Members Last Active: 9 hours ago Posts: 1.5K, Visits: 303.3K	flatbill (1/5/2017) ...the 2 brass plugs that close off the oil galleries at the front in the timing cover area. The machine shop destroyed them taking them out and didn't same the pieces. I think that these plugs have an oil hole in them to lubricate the timing chain. Can anyone confirm these holes and/or the hole diameter? Were both plugs drilled? The plugs are located in the front of the motor and are threaded 1/4 inch tapered pipe thread. I have some brass plugs that will fit but wanted to find the size of the squirt holes. Does anyone know if the FE or 385 motors have the fuel pump eccentric sleeve on the front of the cam? I think the holes send oil to the timing chain. I know this is late but it may help someone else down the line.. . Yes, the plugs (threaded fittings)are drilled. They are similar in appearance to carb jets. The fuel pump eccentric is unique in that it is actually mounted over the cam snout. The pump is actuated by a driving rod similar to a MEL or SBC. LYB roller lifters? ____________________________
	Reply Quote
Ted	Posted 7 Years Ago
Co-Administrator Group: Administrators Last Active: 9 hours ago Posts: 7.3K, Visits: 204.6K	martyk98 (9/7/2017) .......Ref the 390 lifter question, does this make my old 368 roller lifters a rare item or are they available also? The roller lifters for a 368 LYB are expected to be interchangeable with FE engines so probably not a rare item. A roller camshaft for a 368 would be a novelty though. Lorena, Texas (South of Waco)
	Reply Quote
martyk98	Posted 7 Years Ago
Supercharged Group: Forum Members Last Active: Last Year Posts: 160, Visits: 31.8K	My apologies. Never considered a 368 a "true" Y block when I talked to my T Bird friends. Ref the 390 lifter question, does this make my old 368 roller lifters a rare item or are they available also?
	Reply Quote
Lord Gaga	Posted 7 Years Ago
Supercharged Group: Forum Members Last Active: 2 Months Ago Posts: 464, Visits: 183.3K	An FE (Ford, Edsel) is also a Y block. Lord Gaga's Believe it or Don't ! Also, Dumbbells are not bells nor are they dumb! "FREE SAMPLE"
	Reply Quote

Big Y block 368 inch lifters, etc.

Big Y block 368 inch lifters, etc.

Reading This Topic