|
By Glen Henderson - 15 Years Ago
|
 
This is just some of the stuff that I have gathered up to take to Columbus, so bring cash or check. I don't want to bring any of it back. Not pictured are a couple of blocks, 57 hoods and deck lid and maybe a complete 292. I am still digging up stuff, so if you see something that you want more info on send me a message or call (334) 227-3004. All proceeds will go to fund the falcon project. Thanks, Glen
|
|
By MoonShadow - 15 Years Ago
|
|
Glen, Is there a set of skinny slot mags in that pile? Chuck in NH
|
|
By LON - 15 Years Ago
|
|
BRING it ON !!! And bring it to Columbus .The Aussie $ is buying about 90 cents US right now , so it's good to be shopping for car parts .Don't forget to bring ALL those good Y-Block parts with you . Lon
|
|
By Glen Henderson - 15 Years Ago
|
|
No Chuck they are not skinny's (would not be for sale if they were) but a decent set of 4 with pretty good rubber. They are 14 X 7 or 8, never broke them down to measure. Also in the pile are two 14 X 8 new chrome reverse with very little backspace, Other good stuff; G heads C heads C1TE crank 312 crank C1AE rods 312 + .060 block, rods and pistons 292 block 3 ea 57 hoods 57 fairlane deck lid Granada spindles Torino spindles 57 factory A/C vents 57 P/S system (core parts only) and the list goes on and on and on, I didn't know that I had so much stuff. I am still digging and I'm sure that I have more to add. By the way all the S/C stuff is already sold to Chuck.
|
|
By Ol'ford nut - 15 Years Ago
|
|
I see a jack! I'm looking for one for my 56 Fairlane, any luck?
|
|
By speedpro56 - 15 Years Ago
|
|
Glen, do you have a good deck lid for a 57 ford custom? gary
|
|
By Glen Henderson - 15 Years Ago
|
|
That is an orginal 57 jack complete with base plate, lug wrench and the j bolt in excellant unrestored condition. I had planned on getting Tom to give me an apprasial before I put a price on it, but I will listen to offers. Gary the only good deck lid that I have is for a fairlane. I have one for a custom that has a little bubbling and is slightly bent on the left corner, I think it can be repaired with out too much work. If you are interested let me know and I will through it on the wagon, you can look at it and make up your on mind as to condition.
|
|
By y-block don - 15 Years Ago
|
glen will those torino spindles fit a 55 or 57 ? if so send me a price on those and the granada ones 
|
|
By Glen Henderson - 15 Years Ago
|
|
Don, I have never used the Torino spindles, but they are supposed to fit without reaming the balljoint hole and they retain stock ride height, $100. The Granada's reguire reaming the balljoint and lower the front 1" to 2", these that I have look rough (the car sat on the dirt for a long time. They will clean up, but the rotors and calipers are junk good for cores only. $100
|
|
By speedpro56 - 15 Years Ago
|
|
OK Glen, I'll check the 57 custom deck lid in Columbus then and we can go from there. Thanks gary
|
|
By Y block Billy - 15 Years Ago
|
|
I also have a box trailer full of Y parts (over a dozen blocks and sets of heads) along with some 50's to 79 truck parts, any particulars anybody needs that is going to columbus let me know and I will take them to help fund the trip, otherwise I am not taking anything I don't need to. I also have a couple complete sets of mouldings for 54 customline and 54 -56 car parts, What do you Need? and I will let you know if I have it. Regards, Bill
|
|
By charliemccraney - 15 Years Ago
|
|
Got any '61 truck parts?
|
|
By Glen Henderson - 15 Years Ago
|
|
As a matter of fact Charlie, I have a lot of slick parts. What do you need? I also have a couple of slick project trucks that I will sell, but I don't have room to haul that stuff this year. I also have a 57 Fairlane 2 dr H/T project that I am thinking about letting go. Anyone interested, I will try to post a picture.
|
|
By charliemccraney - 15 Years Ago
|
|
I need a solid radiator support and at least the rear half of each front fender.
|
|
By Glen Henderson - 15 Years Ago
|
|
Charlie let me see what I can dig up. Lowrider, I tried to reply to you last PM about the heat riser, but you mailbox is full. My address is: Glen Henderson 6143 Hwy 97 South Letohatchee, AL 36047
|
|
By Glen Henderson - 15 Years Ago
|
|
Charlie, dump your mailbox or call me! 334-799-6577 (cell)
|
|
By charliemccraney - 15 Years Ago
|
|
I made some room in my mail box.
|
|
By Y block Billy - 15 Years Ago
|
|
Charlie, Rear patch panels for the fenders are pretty common and cheap, quality is SO SO, I normally fabricate my own instead of using them to make the seams, etc look more original.
|
|
By y-block don - 15 Years Ago
|
|
hey glen i will take the torino spindals and what price do you have on the hoods and we are in need of some decent 57 fenders see you in c-bus
|
|
By Glen Henderson - 15 Years Ago
|
|
Spindles are yours Don, different prices on the hoods ($150/$300), I may have a couple of fenders that I'll part with, let me think on it. I have one on a parts car that I think is decent if I have time to get it pulled.
|