|
By paul2748 - 6 Years Ago
|
2 G heads. These are take offs and haven't been checked out. Has valves and springs. 225.00 for the set. Plus shipping. I prefer them being picked up as boxing them is a bear but I will ship and as you know these are heavy stuff. Will go UPS and they need a complete address for actual shipping cost so I will have to pack them up and bring to their outlet.to get the actual shipping amount. Can provide additional pics if needed. Heads are not posted and appear to be uncut as the "pads" are slightly over one inch.
|
|
By Ted - 6 Years Ago
|
|
Posted or un-posted?
|
|
By paul2748 - 6 Years Ago
|
I'm not sure and not sure where I should poke my fat fingers to check them. I hoped the markings would tell but I guess not.
|
|
By Ted - 6 Years Ago
|
Here’s a link to the thread explaining how to identify posted ‘G’ heads.
http://forums.y-blocksforever.com/FindPost6764.aspx
|
|
By paul2748 - 6 Years Ago
|
Ted - sent you a PM. The heads are not posted.
|
|
By PF Arcand - 6 Years Ago
|
Paul: Just to clarify, there seems to be a mental hang up for many wanting "G" heads. Based on what I've learned on this site & in Y-B Magazine, for regular use on an engine that does not have Hi Compression pistons and is not equipted with super / turbo charging, unposted heads are just fine. However, the crux is, have the heads been previously milled or need to be reserviced & by how much ?. I believe our lead moderator, Ted, says up to 25 thou is o.k. for regular use..
N.B.- If the engine block has been substantialy decked, the above might not apply?
|
|
By paul2748 - 6 Years Ago
|
I have not measured the block on the head to see it it's been resurfaced. Will do that tomorrow.
PF Arcand (3/20/2019)
Paul: Just to clarify, there seems to be a mental hang up for many wanting "G" heads. Based on what I've learned on this site & in Y-B Magazine, for regular use on an engine that does not have Hi Compression pistons and is not equipted with super / turbo charging, unposted heads are just fine. However, the crux is, have the heads been previously milled or need to be reserviced & by how much ?. I believe our lead moderator, Ted, says up to 25 thou is o.k. for regular use.. N.B.- If the engine block has been substantialy decked, the above might not apply?
|
|
By paul2748 - 6 Years Ago
|
Added new information to original post
|
|
By Tim Quinn - 6 Years Ago
|
Paul, NB: Nota Beni...Note well. You must have taught by the same priest that taught me in High School.
Tim
Friendly Florida Ford Fan (FFFF)
|
|
By paul2748 - 6 Years Ago
|
|
BTTT
|
|
By paul2748 - 5 Years Ago
|
|
Bump
|
|
By paul2748 - 5 Years Ago
|
still available
|
|
By PF Arcand - 5 Years Ago
|
Paul 2748- Sometimes things in the classifieds can be slow here.. You could try a short Ad in Y- Block Magazine if U want. @ PO box 1005, Ottawa IL 61350. $3.00 min. @ .10 Cents/ word, published By- monthly.. Interesting that your not getting any interest in the un cut heads. Especially when you consider that new Aluminum heads run about $2900. U.S. + shipping.. And for street use the "G" heads have the best lower rpm torque ratings of all Y-Blk heads tested...
|
|
By paul2748 - 5 Years Ago
|
Thanks - I get the magazine.
|