|
By Richard - 12 Years Ago
|
|
Need 57 or later trans case T85. Has the side mounted shift.
|
|
By Hoosier Hurricane - 12 Years Ago
|
|
Richard: I have a case, casting # T85C-1A. Has the small (pre '65) Ford/ Mercury bolt pattern. Surface rust from sitting in unheated barn. $35 plus shipping from Indiana.
|
|
By Richard - 12 Years Ago
|
John,
Thats the one I need.
I can send you a check after you figure out shipping
My Address:
Richard Phillips
1954 Oceanaire Drive
San Luis Obispo, CA 93405
|
|
By Hoosier Hurricane - 12 Years Ago
|
|
Richard: I'll get it weighed and get shipping cost. UPS ground OK? Probably 3-4 days to CA. This is the main case only, not tail housing.
|
|
By Richard - 12 Years Ago
|
Yup, Main case only, mine has a broken corner for the bolt hole to the bell housing.
Thanks,
Richard
|
|
By Hoosier Hurricane - 12 Years Ago
|
|
Richard: I went to UPS website for a rate quote, I couldn't get a quote for anything but air freight. I doubt you want to spend $200 to ship, so here's what I'll do. I'll take it to UPS and ship it, then I'll know the cost and let you know. If that won't work for you, I'll take it there and have them weigh it and tell me the cost, and we can go from there. Or you can tell me what you consider the limit for shipping and I can either ship it or take it back home. I've gotten quotes online before, I don't know what happened to their site.
|
|
By Richard - 12 Years Ago
|
John I sent you an email.
Thanks for all your help.
|
|
By Hoosier Hurricane - 12 Years Ago
|
|
Richard: I didn't receive your email. Try sending it directly to feistritzer1<at>msn.com.
Some have had problems forwarding emails through this forum. Substitute @ for <at> in the address.
|
|
By Richard - 12 Years Ago
|
Hey John,
Just pack it up and ship it UPS Ground, let me the total and I will pop a check in the mail. Its no hurry so when ever convient for you. I broke 2/3's of the lower bolt hole corner off mine, but will JB weld the corner back on and use a big washer to use as is. Damn thing fell out when I was putting it back in. I figure next time I replace the clutch I can use the spare case.
The whole problem was related to the gear for the governor. I didn't realize it was a different cut than the old R10, the helicals are cut to the right on the R11 governor and the R10 governor gear goes to left.
Thanks,
Richard Phillips
1954 Oceanaire Drive
San Luis Obispo, CA 93405
|
|
By MoonShadow - 12 Years Ago
|
|
John, Did you try FedEx? They seem more cooperative in shipping odd items. Chuck
|
|
By Glen Henderson - 12 Years Ago
|
|
I have had good luck shipping items up to 70 lbs through the post office.
|
|
By Hoosier Hurricane - 12 Years Ago
|
|
Glenn: Thanks for the info. Moonshadow, no I didn't try FedEx. Richard, not trying to kill the sale but an experienced welder could put the ear back on permanently.
|
|
By Richard - 12 Years Ago
|
John,
I would like to have the case just in case. Ha! Ship it what ever way is convent for you. I am guessing the empty case weighs about 30lbs.
Thanks,
Richard
|
|
By Hoosier Hurricane - 12 Years Ago
|
|
Richard: Sorry to have to do business on this forum, but I can't seem to email you or PM you through this site. Took the case to UPS this morning, they charged me $44.89 to ship ground, you'll have it next Thursday. Personal check is fine, send to John Feistritzer, 800 N. CR 700 E., Selma, IN 47383. To the rest of the guys on the forum, I apologize for having to do it this way.
|
|
By Richard - 12 Years Ago
|
Check in the mail. Yes I could not get your email or pm to work. Regardless Thanks,
Richard
|
|
By Hoosier Hurricane - 12 Years Ago
|
|
Richard: Received your letter yesterday. Thank you.
|
|
By Richard - 12 Years Ago
|
Got the case, nice work on packaging.
Thanks
|